need to set up an IPSec site-to-site VPN between a Cisco/OpeNBSD IPSec-enabled gateway and firewall running PFSense. How do I configure the VPN tunnel so that I can access remote subnet and servers behiend a Cisco firewall/router securely? How do I setup a tunnel mode configuration which will provide you with an encrypted site-to-site network, allowing networks at multiple remote locations to be able to securely communicate using my PFSense located in my SOHO?
Internet Protocol security (IPsec) uses cryptographic security mechanism to protect communications over Internet Protocol (IP) networks. IPSec protocol allows you to authenticate and encrypt all IP traffic between your local office/datacenter/SOHO and remote location. You can pass all traffic over the Internet or through networks which would otherwise be considered insecure.
Our sample setup
Above is a very simple site-to-site VPN, with a security gateway (SOHO and Remote IDC) linking two remote private networks 192.168.1.0/24 and 10.10.29.64/26. Remote IDC VPN is powered by either a Cisco/OpenBSD based system and local SOHO vpn (PFSense) gateways are already configured. From the above, you can see the IPSec config on is as follows:
VPN config provided by a CISCO/OpenBSD gateway located in remote IDC
|Phase 1 config||Savings|
|Your peer IPv4 address||126.96.36.199|
|Cisco/OpenBSD gateway IPv4 address||188.8.131.52|
|Phase 2 config||Values|
|Perfect Forward Secrecy (PFS)||Yes|
|Remote Subnets||10.10.29.64/26 and 10.12.249.192/26|
PFSense appliance VPN IPSec configuration
pfSense must be setup and working properly for the existing local network environment. Both locations must be using non-overlapping LAN IP subnets. For demo purpose my PFSense appliance located at https://192.168.1.254/.
Step #1: Login to admin webui
Fire a browser and type the following url:
Step #2: Setup the VPN Tunnel
Click on VPN > IPSec:
You will see screen as follows. Make sure you check Enable IPsec and click Save to enable IPsec:
Step #3: Configure a new tunnel
Click on + button (see fig.04) to add a new IPsec tunnel Phase 1 configuration. Make sure Interface set to “WAN”, Remote Gateway to “184.108.40.206”, Authentication Method to Pre-Shared key to “YOUR-super-secret-password-key”, Encryption to “3DES”, Authentication to “MD5”, Diffie-Hellman Group to “2”, Keylife to “14400”, and finally press the Save button.
You will see the message as follows on screen:
The IPsec tunnel configuration has been changed. You must apply the changes in order for them to take effect.
Click on the Apply changes button:
Step #4: Create a new Phase 2 config
To create a new Phase 2, click the large + inside the Phase 1 entry in the list, on the left-hand side. This expands the list to display all Phase 2 entries for this Phase 1. Click the + button on the right to add a new entry:
The Phase 2 information must be set as described in Phase 2 config table (see above):
You must set remote network as “10.10.29.64/26”, Protcol to “ESP”, Encrption algorithmes to “3DES”, Hash algothrithms to “MD5”, PFS key group to “2”, lifetime to “3600” and finally click on the Save button and Apply changes button to activate the tunnel.
Step #5: Add IPSec firewall rules
By default firewall rules are automatically added to the WAN to allow the tunnel to connect, but if the option to disable automatic VPN rules is checked, then manual rules may be required. The following rules added by the firewall (you can see them by typing the pfctl -sr | grep -i ipsec command at PFSense console)
anchor "ipsec/*" all pass out on enc0 all flags S/SA keep state label "IPsec internal host to host" pass out route-to (rl0 192.168.0.1) inet proto udp from any to 220.127.116.11 port = isakmp keep state label "IPsec: SL IPsec - outbound isakmp" pass in on rl0 reply-to (rl0 192.168.0.1) inet proto udp from 18.104.22.168 to any port = isakmp keep state label "IPsec: SL IPsec - inbound isakmp" pass out route-to (rl0 192.168.0.1) inet proto udp from any to 22.214.171.124 port = sae-urn keep state label "IPsec: SL IPsec - outbound nat-t" pass in on rl0 reply-to (rl0 192.168.0.1) inet proto udp from 126.96.36.199 to any port = sae-urn keep state label "IPsec: SL IPsec - inbound nat-t" pass out route-to (rl0 192.168.0.1) inet proto esp from any to 188.8.131.52 keep state label "IPsec: SL IPsec - outbound esp proto" pass in on rl0 reply-to (rl0 192.168.0.1) inet proto esp from 184.108.40.206 to any keep state label "IPsec: SL IPsec - inbound esp proto"
To setup IPSec firewall rules as per your needs, click on the Firewall > Rules and IPsec tab. Setup rules as per your needs.
How do I see the current status of the IPSec vpn?
Click on the Status > IPSec:
You will see the screen as follows:
Give it a few seconds to connect to the remote side. Once connected you will see the status as follows:
How do I test my vpn setup?
Try to ping or ssh into one of the remote server:
$ ping -c2 10.10.29.68 PING 10.10.29.68 (10.10.29.68): 56 data bytes 64 bytes from 10.10.29.68: icmp_seq=0 ttl=60 time=267.420 ms 64 bytes from 10.10.29.68: icmp_seq=1 ttl=60 time=271.900 ms --- 10.10.29.68 ping statistics --- 2 packets transmitted, 2 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 267.420/269.660/271.900/2.240 ms $ ssh firstname.lastname@example.org
And, there you have it, VPN up and running from your SOHO.