Credited to :

http://jamesdigioia.com/installing-btrfs-boot-drive-ubuntu-14-04/

http://www.linuxdeveloper.space/install-ubuntu-btrfs/

I recently upgraded my home server; it was previously running Ubuntu 12.04, but it was kind of a mess. I had a 1TB internal drive with 3 separate external drives, running on a HP ProLiant G7 N54L MicroServer. I wanted to accomplish a few things in one fell swoop:

1. Upgrade to Ubuntu 14.04 LTS.
2. Switch to a RAID1

   set up with btrfs.

3. Rearrange my directory set up more logically.

One of the interesting things about btrfs is you can convert an ext4 filesystem to btrfs non-destructively. btrfs maintains a subvolume with the old ext4 data that you can revert to if something goes wrong. Additionally, you can change RAID levels on a live system without any downtime, as well as add or remove drives to your array that way as well.

So after doing some research, I decided I had two options:

1. Upgrade my current system to 14.04, convert the ext4 filesystem to btrfs, add 2 4TB drives, convert to RAID1 and balance the data, rearrange the directory structure, and remove the original 1TB drive.Reason I didn’t go with this: I had some concerns about upgrading to 12.04 “live”, which is required because btrfs wasn’t available in that version.

   I wouldn’t have any backup or way to revert to my old system if something went wrong. Additionally, I had some software installed on my old system that I didn’t really need (MySQL, Apache, plus some drivers for scanners and other things), and a clean install would give me a chance to wipe and reconfigure everything over again.

2. Clean install 14.04 and reinstall/reconfigure everythingThis would take a heckuva lot longer than the first option, but would leave me with a new clean setup after I was finished.

Installation Process

Step 1

Start off by installing Ubuntu 14.04 Server the normal way, with a normal partition structure. A lot of places suggest separating out the /boot partition, but this is no longer necessary. The standard installer will install GRUB to the MBR, so we can boot from there without an issue.

I left off all the software except OpenSSH when I got to the tasksel step. Feel free to do what you’d like there.

Step 2

Once installed, boot into the system and make sure everything is working as expected. Run sudo apt-get update && sudo apt-get upgrade to make sure your software is updated completely. You’ll probably have to reboot afterwards.

Step 3

Boot from a LiveCD and follow these instructions to convert the ext4 system you currently have to a btrfs system. The only thing you should note is the line you prepend with the hash looks a little different:

if [ -n "\${have_grubenv}" ]; then if [ -z "\${boot_once}" ]; then save_env recordfail; fi; fi

Step 4

After you’ve converted to btrfs, boot up. Fingers crossed, everything should boot fine. I ran into an issue where I updated my Linux headers after booting and grub was giving me issues. I had to rerun grub-install and update-grub before it would boot properly.

Step 5

To add the second drive, run the same commands to partition the whole drive as btrfs, then run sudo fdisk -l to get the device name. In my case, it was/dev/sdb, so you’ll see that used in the commands below. Make sure you sub out your device name.

#!bash
sudo btrfs device add /dev/sdb /
sudo btrfs filesystem show /

You’ll get this result:

#!bash
Label: none  uuid: 2b182d08-ae86-423c-8825-22f10554fdca
Total devices 2 FS bytes used 60.68GiB
devid    1 size 3.64TiB used 3.64TiB path /dev/sda2
devid    2 size 3.64TiB used 0.00 path /dev/sdb

Btrfs v3.12    

I don’t know why it shows up as full after the initial mount, but that problem was fixed when I ran the balance command.

I also fiddled with getting them to mount correctly before successfully adding it to the root drive. A lot of tutorials keep telling you to add to /mnt, but don’t listen to them – we’re using it as our main drive so add to /.

After its been added, balance the drives:

#!bash
sudo btrfs balance start -dconvert=raid1 -mconvert=raid1 /

dconvert converts the data stories to RAID1, mconvert manages the metadata.

The balance command is where a lot of the magic happens. btrfs is able to rearrange the data into whatever setup you’d like.

Converts to:

#!bash
dreedle@pianosa:~$ sudo btrfs fi show /
Label: none  uuid: 2b182d08-ae86-423c-8825-22f10554fdca
Total devices 2 FS bytes used 59.97GiB
devid    1 size 3.64TiB used 62.03GiB path /dev/sda2
devid    2 size 3.64TiB used 62.03GiB path /dev/sdb

Btrfs v3.12